Так же Вы можете заказать данную позицию по тел.: +7 (812) 200-96-95
Safety-related parameters
Safety integrity level:
SIL2 (IEC 61508), SILCL2 (IEC 62061)
Category:
3 (EN ISO 13849)
Performance level:
PL d EN ISO 13849 1)
TM (mission time):
20 a (EN ISO 13849)
Maximum demand rate:
Continuous (analog signals)
PFHD: probability of dangerous failure per hour:
1.0 * 1E-08 2)
MTTFd: mean time to dangerous failure:
1,073 a (EN ISO 13849)
footnote
1) For more detailed information on the exact configuration of your machine/unit, please consult your relevant SICK branch office. 2) The values displayed apply to a diagnostic degree of coverage of 90%, which must be achieved by the external drive system
Performance
Number of sine/cosine periods per revolution:
1,024
Number of the absolute ascertainable revolutions:
4,096 (Multiturn)
Total number of steps:
134,217,728
Measuring step:
0.3 angular seconds at interpolation of the sine/cosine signals with e.g. 12 Bit
Differential non-linearity:
± 7 angular seconds (Non-linearity within a sine/cosine period)
Operating speed:
6,000 /min, up to which the absolute position can be reliably produced
Available memory area:
128 Byte, 128 Byte (E2PROM 512)
Integral non-linearity typ.:
± 45 angular seconds (Error limits for evaluating sine/cosine period) without mechanical tension of the stator coupling
Механические параметры
Flange type/stator coupling:
Rubber support
Dimensions:
See dimensional drawing
Moment of inertia of the rotor:
10 gcm?
Maximum operating speed:
12,000 /min
Maximum angular acceleration:
200,000 rad/s?
Operating torque:
0.2 Ncm
Start up torque:
0.4 Ncm
Permissible shaft movement, radial, static:
± 0.5 mm
Permissible shaft movement, radial, dynamic:
± 0.1 mm
Permissible shaft movement, axial, static:
± 0.75 mm
Permissible shaft movement, axial, dynamic:
± 0.2 mm
Life of ball bearings:
3.6 x 10^9 revolutions
Connection type:
Cable, 8-pin, radial, 200 mm
Shaft version:
Tapered shaft
Angular motion perpendicular to the rotational axis, static:
± 0.005 mm/mm
Angular motion perpendicular to the rotational axis, dynamic:
± 0.002 mm/mm
GEWICHT01:
0.2 kg
Электрические параметры
Electrical interface:
HIPERFACE
Operating voltage range/supply Voltage:
7 V DC ... 12 V DC
Recommended supply voltage:
8 V DC
Output frequency for sine/cosine signals:
0 kHz ... 200 kHz
Operating power consumption (no load):
80 mA 1)
footnote
1) Without load
Interfaces
Type of code for the absolute value:
Binary
Code sequence:
Increasing, for clockwise shaft rotation, looking in direction 'A' (see dimensional drawing)
Interface signals:
Parameter channel RS 485: digital, Process data channel SIN, REFSIN, COS, REFCOS: analog, differential
Ambient data
Working temperature range:
-30 °C ... +115 °C
Storage temperature range:
-40 °C ... +125 °C, without package
Relative humidity / Condensation:
90 %, Condensation not permitted
Resistance to shocks:
100 g / 10 ms / according to EN 60068-2-27
Resistance to vibration:
20 g / 10 Hz / 2,000 Hz / according to EN 60068-2-6
EMC:
(according to EN 61000-6-2 and EN 61000-6-3) 1)
Enclosure rating:
IP 40 (according to IEC 60529), with mating connector inserted
footnote
1) The EMC according to the standards quoted is achieved when the motor feedback system is mounted in an electrically conductive housing, which is connected to the central earthing point of the motor controller via a cable screen. This is also where the GND (0 V) connection of the power supply voltage is linked to earth. Users must perform their own tests when other screen designs are used.
